Search results

Create the page "S" on this wiki! See also the search results found.

• IGVC
  |eventstart = Let's go | Jaymi's design report was submitted for Woodi.
  4 KB (603 words) - 22:26, 31 May 2020
• Budgeting for Travel
  ...arty companies, like Expedia, we must book direct from the airlines via GT's travel agency, Travel Inc.
  2 KB (260 words) - 19:30, 14 July 2018
• RoboNav
  |eventstart = Let's go | Jaymi's design report was submitted for Woodi.
  5 KB (612 words) - 11:44, 29 October 2023
• Blasphemi
  ***[Blasphemi (loser) V.S. Off Killter (winner): https://youtu.be/U74VuuBT5oI] **** Blasphemi's weapon worked very effectively at the start of the match. The ring took mul
  6 KB (940 words) - 16:43, 29 June 2022
• IT Coordinator
  ...artments move to MDT and SCCM, RoboJackets will join either ME IT's or ITG's implementation.
  4 KB (747 words) - 19:43, 22 May 2020
• Trixxie
  ...The base has three layers in ascending order: a level for holding Trixxie's heavy batteries, a mid level for holding electronics and the laptop, and a #Video Out Port (S-Video)
  5 KB (704 words) - 18:53, 30 June 2019
• 3lb Documentation Guide
  (Replace this text with an overall introduction of your robot's design, name, features, ect)
  3 KB (331 words) - 18:47, 12 November 2018
• RCCamera
  ...with wide angle lenses. They did not stream from firewire, but rather used S-Video and a capture card per camera. They used the deinterlaced frames to
  3 KB (410 words) - 21:52, 13 June 2018
• RJJS Info
  The RoboJackets' JumpStart program's goal is to ensure the developement of sustainable FIRST Robotics Competitio
  2 KB (310 words) - 14:08, 22 July 2018
• RoboCup: Redesign 2014-2015
  ==== <s>To Do</s> ==== ...rg/wiki/Serial_Peripheral_Interface_Bus SPI] with a current FPGA and mbed</s>
  29 KB (4,004 words) - 22:39, 13 June 2018
• Guillotini
  **** Dizzi's weapon and drive system also had issues, preventing it from spinning up to **** one last hit and the Guillotini's battery popped out, judges terminated battle
  5 KB (755 words) - 13:51, 14 May 2021
• Chonki Design Guide
  ..., so feet would always be in contact with the ground through the cam shaft's rotation. To fit inside the feet get smaller as they move away from the cha *Lives up the it's name
  7 KB (1,175 words) - 02:50, 9 April 2022
• RC09-Carpet
  ...None of them had supplies of this carpet but suggested Home Depot and Lowe's. One company also gave optimistism about Myers near Atlantic Station (Nort
  2 KB (319 words) - 20:50, 24 May 2020
• RoboCup Simulator Execution
  In this case, we will only drive one team. The other team's robots will remain stationary.
  2 KB (387 words) - 23:12, 13 June 2018
• RoboWrestling
  ...ed with magnets) to simulate real sumo wrestlers’ sturdiness. At the judge's call, the robots will then proceed to try and push each other off of the ri
  2 KB (278 words) - 23:11, 23 May 2024
• Velociti
  ...inner designed and manufactured in 2021-2022. Velociti's weapon is roughly S-shaped and the frame mostly follows a standard puzzle fit box design with t **** After clutching up the safety inspection, Velociti's first opponent was a D2 kit bot wedge
  14 KB (2,103 words) - 01:36, 2 July 2023
• Electrical Room Equipment
  ...le:Logic16 ScreenshoSat.jpg|thumb|none|300px|Screenshot showing the Saleae's logic16 capturing program]]
  3 KB (384 words) - 22:45, 13 June 2018
• Waluigi
  | 0.34 s (theoretical) | Roughly 8 ft/s
  5 KB (827 words) - 00:00, 23 April 2023
• RC08-Chipper
  * .75" diameter, 1.5" long, pull type tubular solenoid, model number S-15-75 ...only the kinetic energy of the ball was used, at its maximum value of 10 m/s
  5 KB (687 words) - 20:49, 24 May 2020
• RoboJackets Brand Standards
  ...to be half the width of the Text. The distance between the tip of RoboBuzz's drill/stinger and the top of the J in RoboJackets should be 1/24th the widt
  2 KB (353 words) - 21:12, 1 July 2019

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)