Chonkii

From RoboJackets Wiki
Revision as of 01:23, 9 April 2022 by Bnaing3 (talk | contribs)
Jump to navigation Jump to search

Introduction

This robot had a name before a design. It born when Brian thought to himself, "Hey, it would be really funny if we named a robot Chonki and made it really, really big and really really loud..." Throughout the design process the robot lived up to its name. Chonkii is a 45lb shuffling shell spinner competing in the 30lb weight class that serves as an iteration on the original Chonki, which was never fully constructed. It was developed during 2021-2022. The drive system was iterated from that of Apachi and Chonki. The weapon system was a brand new concept for BattleBots. The goal of Chonki was to evaluate the viability of shell spinners while taking advantage of the 1.5 times weight multiplier afforded by using a mechanism other than wheels for movement. Competed at Motorama 2022 and finished with a 2-2 record.

Members:

  • Mihir Nagaraj (Lead)
  • Brian Epstein (Mentor)
  • Janie Edgar
  • Sydney Baker
  • Thomas Jackson
  • Cole Sosnowski
  • Christopher Bellflowers
  • Emily Liu

Drive System

Chonki utilizes a shuffler system for drive. It consists of two shuffler modules, each with 4 UHMWPE feet. The feet sit on two parallel, keyed cam shafts. These allowed for the four feet to be positioned 90 degrees from each other, so feet would always be in contact with the ground through the cam shaft's rotation. To fit inside the feet get smaller as they move away from the chassis. The longer feet have fillets to clear the rollers and support which they sit under. The cams have offset keyed holes to accommodate the shafts and sit inside circular cutouts in the feet, which keep them parallel with the ground as it walks. The use of the shuffling system allowed Chonki a weight bonus, bringing the max weight to 45 lbs.

Foot Profile

Cams and Bearings

Drive Gears

Weapon System

Design Considerations

Since the weapon on this bot also serves as its armor, it was imperative that the weapon be large enough for the robot to fit inside. An additional constraint was that it must be small enough that a reasonable thickness could be attained while still remaining under the desired percentage of the total weight of the robot (~50%).

Shell Design

Shell was milled out of a 250 lb block of A36 steel. It took forever but was very effective in absorbing damage.


Pros:

  • Less expensive than the nested ring design
  • Made from one solid piece so it didn't have connection points to fail at
  • Lives up the it's name, super THICCC
  • Its SHINY!

Cons:

  • Expensive, had to get Speed Machine to have them use a larger machine to mill the shell out.
  • One piece, parts that got damaged on shell were not replaceable - dents needed to be pressed or hammered out.

Weapon Shaft Interface

A tapered roller bearing fits into a housing that is attached to the top of the shell.

Bearing Section View.PNG

Weapon-Drive Mechanism

    • Inspired by Hyperpolarized, it was later decided to drive the weapon by using a single driven wheel at the top of the bot, with rollers along the surface to give additional support. A central shaft was used as a dead axle support.

Chassis System

File:ChonkiiChassis.png

  • The chassis mostly consisted of aluminum, featuring of a ¼” top and side plates and ⅛” bottom plate.
  • The front and back plates were made of HDPE, which bent to form Chonkii’s robustly round shape.
  • The chassis had multiple rollers spaced out along its top, giving additional support to the shell track above.
  • The central dead axle was constrained by two blocks, mounted to both the top and bottom plates. However, it was later determined that a single longer block with a key would constrain the shaft better than the two block system.
    • While drilling through the blocks into the shaft, a drill bit melted inside, acting as a makeshift pin (that was instantly destroyed in competition).

Electronics

Drive Motors Turnigy Aerodrive SK3 - 5055-280KV Brushless Outrunner Motor


Drive Motor Controllers Flipsky Dual FSESC6.6 Based upon VESC6 with Aluminum Heatsink Mini Size (whatever apachi used)
Weapon Motor Scorpion SII-4035-250KV
Weapon Motor Controllers Tribunus 06-120A (6S) Brushless ESC
Receiver Hobby King 2.4Ghz Receiver 6Ch V2
Remote Control Hobby King 2.4Ghz 6Ch Tx and Rx V2
Battery Turnigy Heavy Duty 5000mAh 6S 60C LiPo Pack w/XT90
Turnigy Graphene Panther 3000mAh 3S 75C Battery Pack w/XT90

Competitions

Motorama 2022

  • Results: 2-2
    • Bracket Style: Double Elimination
      • [Chonkii (winner) V.S. Marathon (loser): YouTube Link]
        • This match saw Chonkii head to head with a
        • Chonkii got a bunch of good hits in, sparks flew multiple times.
        • Shove, wall , stay
        • More Description
      • [Chonkii (loser) V.S. Yahoo (winner): YouTube Link]
        • turtle
        • More Description
      • [Chonkii (winner) V.S. Pigeon (loser): YouTube Link]
        • Trick shots, smacked off titanium front plate
        • More Description
      • [Chonkii (loser) V.S. Lockout (winner): YouTube Link]
        • Forfeit (5 thou)
        • More Description
    • Robojacket Rumble
      • [Chonkii vs Everyone: YouTube Link]
        • Description
        • More Description

Issues

  • Stuff
  • Other Stuff

Changes to make

  • Stuff
  • Other Stuff

Trivia

  • The Vectrax was rendered inoperable twice by Chonki members (mainly Brian) during its construction.