Difference between revisions of "Anarchi"
Jump to navigation
Jump to search
(→Introduction) |
|||
Line 80: | Line 80: | ||
=== [[Motorama_2022|Motorama 2022]] === | === [[Motorama_2022|Motorama 2022]] === | ||
− | *Results: | + | *Results: 1-2 |
**Bracket Style: Double Elimination | **Bracket Style: Double Elimination | ||
− | ***[ | + | ***[Anarchi (loser) V.S. Wedgeham (loser): YouTube Link] |
− | **** | + | **** |
− | **** | + | **** |
− | **** | + | **** |
− | + | **** | |
− | + | ***[Anarchi (winner) V.S. Dragon Fruit (loser): YouTube Link] | |
− | **** | + | **** |
− | + | **** | |
− | ***[ | + | ***[Anarchi (loser) V.S. Crippling Depression (winner): YouTube Link] |
− | **** | + | **** |
− | **** | + | **** |
− | ***[ | ||
− | **** | ||
− | |||
− | |||
− | |||
− | |||
− | **** | ||
==== Issues ==== | ==== Issues ==== |
Revision as of 00:11, 17 May 2022
Contents
Introduction
Members:
- Dylan Adriano (Bot Lead)
- Brian Naing
- Cade Tyler
- Jackson Isenberg
- Lucas Luwa
Drive System
Foot Profile
Weapon System
Design Considerations
Shell Design
Shell was milled out of a 250 lb block of A36 steel. It took forever but was very effective in absorbing damage.
Pros:
Cons:
- Expensive, had to get Speed Machine to have them use a larger machine to mill the shell out.
- One piece, parts that got damaged on shell were not replaceable - dents needed to be pressed or hammered out.
Weapon Shaft Interface
A tapered roller bearing fits into a housing that is attached to the top of the shell.
Weapon-Drive Mechanism
- Inspired by Hyperpolarized, it was later decided to drive the weapon by using a single driven wheel at the top of the bot, with rollers along the surface to give additional support. A central shaft was used as a dead axle support.
Chassis System
- The chassis mostly consisted of aluminum, featuring of a ¼” top and side plates and ⅛” bottom plate.
- The front and back plates were made of HDPE, which bent to form Chonkii’s robustly round shape.
- The chassis had multiple rollers spaced out along its top, giving additional support to the shell track above.
- The central dead axle was constrained by two blocks, mounted to both the top and bottom plates. However, it was later determined that a single longer block with a key would constrain the shaft better than the two block system.
- While drilling through the blocks into the shaft, a drill bit melted inside, acting as a makeshift pin (that was instantly destroyed in competition).
Electronics
Drive Motors | Turnigy Aerodrive SK3 - 5055-280KV Brushless Outrunner Motor
|
Drive Motor Controllers | Flipsky Dual FSESC6.6 Based upon VESC6 with Aluminum Heatsink Mini Size (whatever apachi used) |
Weapon Motor | Scorpion SII-4035-250KV |
Weapon Motor Controllers | Tribunus 06-120A (6S) Brushless ESC |
Receiver | Hobby King 2.4Ghz Receiver 6Ch V2 |
Remote Control | Hobby King 2.4Ghz 6Ch Tx and Rx V2 |
Battery | Turnigy Heavy Duty 5000mAh 6S 60C LiPo Pack w/XT90
Turnigy Graphene Panther 3000mAh 3S 75C Battery Pack w/XT90 |
Competitions
Motorama 2022
- Results: 1-2
- Bracket Style: Double Elimination
- [Anarchi (loser) V.S. Wedgeham (loser): YouTube Link]
- [Anarchi (winner) V.S. Dragon Fruit (loser): YouTube Link]
- [Anarchi (loser) V.S. Crippling Depression (winner): YouTube Link]
- [Anarchi (loser) V.S. Wedgeham (loser): YouTube Link]
- Bracket Style: Double Elimination
Issues
- Stuff
- Other Stuff
Changes to make
- Stuff
- Other Stuff
Trivia
- The Vectrax was rendered inoperable twice by Chonki members (mainly Brian) during its construction.