RC09-KickerChipper

As part of the RoboCup 2010 Mechanical, the kicker provides passing capabilities to the robots. It is part of the chipper / kicker assembly.

2010 RoboJackets RoboCup Kicker & Chipperl

Related Pages

• Kicker Electronics

Parts & Components

Amounts are based on per robot. Materials are in sizes for prototyping not lowest cost per amount.

Stock

Chipper Solenoid

Vendor - Solenoid City

Part No. - S-20-90-24

Cost - $38.26

Description - Chipper Solenoid S-20-90-24

Kicker Solenoid

Vendor - Solenoid City

Part No. - S-29-150-20HF

Cost - $93.93

Description - Kicker Solenoid S-29-150-20HF

Aluminum Kicker Plunger

Vendor - McMaster-Carr

Part No. - 8974K25

Cost - $12.37

Description - Multipurpose Aluminum (Alloy 6061), 7/16" Diam, 36"

Kicker Bronze Bushing

Vendor - McMaster-Carr

Part No. - 6338K462

Cost - $0.91

Description - SAE 841 Bronze Flanged-Sleeve Bearing for 7/16" Shaft Diameter, 9/16" OD, 1/2" Length

Chipper Arm Ball Bearing

Vendor - Grainger

Part No. - 1ZEH7

Cost - $7.69

Description - Mini Ball Bearing,Flanged,Bore 0.1250 In

Front Solenoid Mount

Vendor - McMaster-Carr

Part No. - 9008K461

Cost - $20.35

Description - Multipurpose Aluminum (Alloy 6061) 1-1/2" Square, 1' Length

Middle Solenoid Mount

Vendor - McMaster-Carr

Part No. - 9246K51

Cost - $36.66

Description - Multipurpose Aluminum (Alloy 6061) 3/4" Thick, 8" X 8"

Rear Solenoid Mount

Vendor - McMaster-Carr

Part No. - 9008K461

Cost - $20.35

Description - Multipurpose Aluminum (Alloy 6061) 1-1/2" Square, 1' Length

Rear Solenoid Mount

Vendor - McMaster-Carr

Part No. - 9246K21

Cost - $21.34

Description - Multipurpose Aluminum (Alloy 6061) 3/8" Thick, 8" X 8"

Plunger Stabilizer

Vendor - McMaster-Carr

Part No. - 9246K21

Cost - $21.34

Description - Multipurpose Aluminum (Alloy 6061) 3/8" Thick, 8" X 8"

Kicker Set Screw

Vendor - McMaster-Carr

Part No. - 91375A196

Cost - $13.56

Description - Steel Standard Socket 8-32 x .625"

Chipper Arm Ball Bearing

Vendor - Grainger

Part No. - 1ZEH7

Cost - $7.69

Description - Mini Ball Bearing,Flanged,Bore 0.1250"

Chipper Arm Connector

Vendor - McMaster-Carr

Part No. - 90145A451

Cost - $11.05

Description - 18-8 Stainless Steel Dowel Pin 3/32" Diameter, 2" Length

Manufacturing and Assembly

Slots for solenoids in solenoid mounts are milled with + .01" tolerance

Casing was removed from kicker solenoid and bobbin was inserted between the front and middle solenoid mounts

Bronze bushing were inserted into the front and middle solenoid mounts that support the plunger kicker

The plunger kicker is assembled from 7/16" steel and aluminum. The front half of the plunger that is attached to the kicker boot is made of aluminum. It is attached to the steel half of the plunger with an 8-32 5/8" set screw. This allows the plunger to be pulled forward the first half of the stroke without it being pulled back during the second half.

Chipper arms were made to allow room for a wider kicker boot and prevent collision with nearby components. They were placed so that during chipping, the direction of the chipper boot at the point of contact with the ball moves straight towards the balls center. This ensures the as much energy as possible from chipping goes towards the translational (kinetic) energy of the ball instead of rotational.

NOTE: 2.4in long by .247in tall by .302in deep 7075 Grade, #8 32threads/in(8-32)

Action Log

1. 10/12/2008 - Solenoid inner core diameter for prototype selected.
2. 03/04/2009 - Fabrication issues with quality control have been encountered in winding the solenoid.
3. 03/13/2009 - Decision has been made to purchase more of last years solenoids and attempt in house modifications.
4. 03/22/2009 - Initial concept completed.
5. 04/04/2009 - Resizing adjustments made.
6. 04/12/2009 - Kicker rev1 design completed.
7. 10/25/2009 - First fully machineable chipper design completed. (rev8)
8. 01/31/2010 - Prototype kicker and chipper OTS solenoids re selected and designs updated.
9. 01/31/2010 - Hardware testing of new electrical mockup shows estimated speeds of 12 m/s with 2008 solenoids.
10. 02/02/2010 - New solenoids ordered.
11. 02/07/2010 - Chipper & Kicker assemblies updated.
12. 03/25/2010 - Chipper variants assembled and tested. Variants non functional.
13. 03/26/2010 - Redesign completed, separate test rig designed, and fabrication started.
14. 03/27/2010 - Fabrication completed and device tested. Chipper working with a range of up to 13ft. Longer solenoid stroke need for better power transfer.
15. 04/04/2010 - Design refinements conducted.