Difference between revisions of "WakiSmaki"
Jump to navigation
Jump to search
(→Changes/Improvements) |
(→WakiSmaki) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 37: | Line 37: | ||
*Results: 0/2 | *Results: 0/2 | ||
**Bracket Style: Double Elimination | **Bracket Style: Double Elimination | ||
| − | ***[ | + | ***[https://youtu.be/jfENAwaXAu8 loss vs Deadeight (Drum Kitbot)] |
****Vertical hit took off the ring | ****Vertical hit took off the ring | ||
****All Nylon flywheels came off their flanges by coming off diagonally | ****All Nylon flywheels came off their flanges by coming off diagonally | ||
****Bot we lost to: http://www.teamrollingthunder.com/Kitbots/3lb_Kits/Weta_2/body_weta_2.html | ****Bot we lost to: http://www.teamrollingthunder.com/Kitbots/3lb_Kits/Weta_2/body_weta_2.html | ||
| − | ***[ | + | ***[https://youtu.be/M5PLtmMmN7s loss vs Mux] |
****Took a couple hits to the ring before it came off | ****Took a couple hits to the ring before it came off | ||
****Flywheels failed again | ****Flywheels failed again | ||
| Line 90: | Line 90: | ||
* Did not take any damage when spinning properly | * Did not take any damage when spinning properly | ||
* Actually spun up | * Actually spun up | ||
| + | * Drive worked and never took any damage | ||
==== Changes/Improvements ==== | ==== Changes/Improvements ==== | ||
| Line 97: | Line 98: | ||
* Use more plastic on low stress components | * Use more plastic on low stress components | ||
* You can buy urethane coated bearings. We probably would have used that if we knew. | * You can buy urethane coated bearings. We probably would have used that if we knew. | ||
| + | |||
| + | === WakiiSmakii === | ||
| + | |||
| + | Broke before it could compete. | ||
| + | |||
| + | ==== Changes Made ==== | ||
| + | |||
| + | * New Flywheel design with thrust bearings to hold flywheels from above | ||
| + | * New Tooth design | ||
| + | * New top and bottom plates | ||
| + | |||
| + | ==== Problems ==== | ||
| + | |||
| + | * Electronics needed to be held more strongly. | ||
== Notes: == | == Notes: == | ||
Latest revision as of 19:59, 4 April 2019
| WakiSmaki | |
|---|---|
 | |
| Year Of Creation | 2018-2019 |
| Versions | |
| Current Version | 1.0 |
| Wins/Losses | 0/2 |
| Information and Statistics | |
| Weight Class | BeetleWeight |
| Weapon Class | Ring Spinner |
| Combined Wins/Losses | 0/2 |
WakiSmaki is a 3lb ring spinner which features a simple flywheel design with 5 flywheels. It had a direct drive with a wheel attached to a motor that drove the two part ring. The ring had an interior channel that the weapon drive and flywheels resided in.
Contents
Competitions
Motorama 2019
- Results: 0/2
- Bracket Style: Double Elimination
- loss vs Deadeight (Drum Kitbot)
- Vertical hit took off the ring
- All Nylon flywheels came off their flanges by coming off diagonally
- Bot we lost to: http://www.teamrollingthunder.com/Kitbots/3lb_Kits/Weta_2/body_weta_2.html
- loss vs Mux
- Took a couple hits to the ring before it came off
- Flywheels failed again
- loss vs Deadeight (Drum Kitbot)
- Bracket Style: Double Elimination
Versions
WakiSmaki
Created by: Dylan Fife, Brian Epstein, Zachary Ghezzi, Andrew Teske
| Drive Motors | DYS BE1806 2300KV Motors |
| Drive Motor Gearboxes | KITBOTS 1000rpm Gearmotor Gearboxes |
| Drive Motor Controllers | DYS 20A Micro Opto Multi-rotor ESC |
| Weapon Motor | PROPDRIVE v2 2836 3000KV Brushless Outrunner Motor |
| Weapon Motor Controllers | TURNIGY Plush 60amp Speed Controller w/BEC |
| Receiver | Turnigy T6A-V2 AFHDS 2.4GHz 6Ch Receiver V2 |
| Remote Control | Turnigy T6A-V2 AFHDS 2.4GHz 6Ch Transmitter V2 |
| Battery | Turnigy Nano-Tech 1000mAh 3s 45~90c LiPo Pack |
Problems
- Flywheels came off because they were held in with a press fit and a flange
- Weapon drive wheel ballooned and went over the cap that was supposed to hold it in
- Lower RPM compared to drums makes it so that it gets hit first
- Because our orders went out of stock (VEX) we had to redesign last minute and went overweight
- We should have done weight savings on anything we could have
Good aspects
- Did not take any damage when spinning properly
- Actually spun up
- Drive worked and never took any damage
Changes/Improvements
- Retain flywheels better
- Make weapon drive wheel out of a hard rubber. DO NOT USE SILICONE
- Use more plastic on low stress components
- You can buy urethane coated bearings. We probably would have used that if we knew.
WakiiSmakii
Broke before it could compete.
Changes Made
- New Flywheel design with thrust bearings to hold flywheels from above
- New Tooth design
- New top and bottom plates
Problems
- Electronics needed to be held more strongly.
Notes:
(random joke, optional)
(Naming inspiration, optional)
(Names of original builders)
