Difference between revisions of "2015 Chipper"
Jump to navigation
Jump to search
Joldenburg6 (talk | contribs) m (Categorize) |
|||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
== The Goal == | == The Goal == | ||
| − | The goal when creating the chipper was to simplify the design. We incorporated a [ | + | The goal when creating the chipper was to simplify the design. We incorporated a [http://wiki.robojackets.org/w/RC15-FlatSolenoid Flat Solenoid] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards. |
| + | |||
| + | == Armature Distance Tests == | ||
| + | |||
| + | Tests were performed on 11/15/15 to test the distance the armature needs to be outside the chipper solenoid to maximize power output. The armature distance was measured from the front of the armature (the side without the hole). The spring remained unattached for all of the tests conducted. | ||
| + | |||
| + | {| border="1" cellspacing="1" cellpadding="1" style="width:500px;" | ||
| + | |- | ||
| + | | '''Armature distance from front edge (in)''' | ||
| + | | '''Ball distance (in)''' | ||
| + | | '''1st bounce distance (in''') | ||
| + | |- | ||
| + | | .5 | ||
| + | | 34.5 | ||
| + | | 10.5 | ||
| + | |- | ||
| + | | <span style="background-color:#FFD700;">.7</span> | ||
| + | | <span style="background-color:#FFD700;">40-44</span> | ||
| + | | <span style="background-color:#FFD700;">17</span> | ||
| + | |- | ||
| + | | .9 | ||
| + | | - | ||
| + | | | ||
| + | 10 | ||
| + | |||
| + | |- | ||
| + | | 1.1 | ||
| + | | 28 | ||
| + | | 8.5 | ||
| + | |- | ||
| + | | 1.3 | ||
| + | | 14 | ||
| + | | 4 | ||
| + | |- | ||
| + | | 1.5 | ||
| + | | 1.5 | ||
| + | | 3 | ||
| + | |} | ||
| + | |||
| + | The maximum determined distance was still insufficient for the chipper to gain any significant vertical distance. | ||
| + | |||
| + | [[Category:RoboCup]][[Category:2015-2016]] | ||
Latest revision as of 20:49, 13 June 2018
The Goal
The goal when creating the chipper was to simplify the design. We incorporated a Flat Solenoid as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.
Armature Distance Tests
Tests were performed on 11/15/15 to test the distance the armature needs to be outside the chipper solenoid to maximize power output. The armature distance was measured from the front of the armature (the side without the hole). The spring remained unattached for all of the tests conducted.
| Armature distance from front edge (in) | Ball distance (in) | 1st bounce distance (in) |
| .5 | 34.5 | 10.5 |
| .7 | 40-44 | 17 |
| .9 | - |
10 |
| 1.1 | 28 | 8.5 |
| 1.3 | 14 | 4 |
| 1.5 | 1.5 | 3 |
The maximum determined distance was still insufficient for the chipper to gain any significant vertical distance.
