Difference between revisions of "RCMeetingMinutes"
Jump to navigation
Jump to search
| Line 1: | Line 1: | ||
| − | + | This document represents the results of a meeting held 8/29/08 where the core members discussed plans for the 2009 system. | |
==Team Roadmap== | ==Team Roadmap== | ||
| Line 15: | Line 15: | ||
* "Fall Classic" with MIT and CMU? - possibly in the Spring? | * "Fall Classic" with MIT and CMU? - possibly in the Spring? | ||
* RoboCup 2009 in Austria | * RoboCup 2009 in Austria | ||
| − | + | ||
| − | ==General Electrical | + | ==Status Quo Features== |
| + | ===General Electrical Features=== | ||
*LiPo Batteries | *LiPo Batteries | ||
*Battery Maintenance/Charging circuitry | *Battery Maintenance/Charging circuitry | ||
| Line 25: | Line 26: | ||
**Serial debug port | **Serial debug port | ||
**Debug switches | **Debug switches | ||
| − | * | + | |
| − | * | + | ===Control Board Features=== |
| − | *** | + | * Bugfix and remake of 2008 boards (see [[RC082ndBoardErrata | 2.0 Board Errata]]) |
| − | ***Add support for chipping | + | ** Will keep motor driver circuitry |
| − | + | ** New ARM | |
| − | + | ** Possible serial interface between FPGA and ARM | |
| − | * | + | * New [[RoboCup_Radio_2009|radios]] |
| − | + | ** Smaller, cheaper, in an emptier area of the spectrum | |
| − | + | ||
| − | + | ===Ball Control (mechanical and electrical) Features=== | |
| + | * Measure charge voltage | ||
| + | * Add support for chipping | ||
| + | * Exceed regulation kicking speed | ||
| + | * [[RC09BallSense|Ball sensor]] | ||
| + | |||
| + | Mechanical | ||
| + | **Encoder | ||
| + | **Support for chipping | ||
***Lower CG | ***Lower CG | ||
****Being able to reliably stop from max speed without flipping | ****Being able to reliably stop from max speed without flipping | ||
Revision as of 16:36, 10 September 2008
This document represents the results of a meeting held 8/29/08 where the core members discussed plans for the 2009 system.
Contents
Team Roadmap
- Document our system
- Testing
- Design document
- Refurbish 2008 robots so software can develop
- Reduce wheel play
- Investigate ball sensors?
- "Status Quo" Robots
- Performance Numbers
- Theirs
- Ours
- Complete team by Jan 2009
- Performance Numbers
- "Fall Classic" with MIT and CMU? - possibly in the Spring?
- RoboCup 2009 in Austria
Status Quo Features
General Electrical Features
- LiPo Batteries
- Battery Maintenance/Charging circuitry
- Battery lifetime, charge/discharge estimates, "fuel gauge"
- User interface daughter card
- LEDs visible outside shell LEDS
- Better access to on switch
- Serial debug port
- Debug switches
Control Board Features
- Bugfix and remake of 2008 boards (see 2.0 Board Errata)
- Will keep motor driver circuitry
- New ARM
- Possible serial interface between FPGA and ARM
- New radios
- Smaller, cheaper, in an emptier area of the spectrum
Ball Control (mechanical and electrical) Features
- Measure charge voltage
- Add support for chipping
- Exceed regulation kicking speed
- Ball sensor
Mechanical
- Encoder
- Support for chipping
- Lower CG
- Being able to reliably stop from max speed without flipping
- Competitive Accel/Decel
- Smaller drive modules
- Less Maintenance of drive module and rollers
- Ground Clearance
- Lower CG
- Software
- Parameter extraction and estimation
- Ability to switch which side of field
- Burin tests/stress
- World model/Data filtering/prediction
- Probabilistic sensing
- Integration/communication
- Timing/Profiling of how our system works
- Motion control
- Calibration
- SW test for hardware performance
- Use tech challenges as a springboard
- Software
All teams will have clearly defined goals and plan to complete said goals
- General
- More practice time
- Make a real field
- Goals
- Walls
- Location
- RefBox
- General
- New Prototypes
