EAGLE Style Guide

From RoboJackets Wiki
Revision as of 00:28, 11 July 2020 by Asrinivasan77 (talk | contribs)
Jump to navigation Jump to search

Part Creation

Symbol

Grid

  • Size: 0.1 in
  • Alt: 0.01 in

Name

  • Should be manufacturer part/family number (eg. ATTINY167-SU)

Description

  • Leave blank

Style

  • Origin
    • Center origin (crosshair) on symbol center
  • Text
    • Keep text horizontal
    • Size: 0.07 in
    • Ratio: 8%
    • Line Distance: 50%
    • Font: proportional
  • Name
    • Locate in top left of symbol
    • Align: bottom-left
    • Layer: 95 Names
    • Value: >NAME
  • Value
    • Locate in bottom-left of symbol
    • Align: top-left
    • Layer: 96 Values
    • Value: >VALUE
  • Outline
    • Use Lines
      • Width: 0.01 in
      • Style: continuous
      • Layer: 94 Symbol
      • Curve: 0
    • Try to have a length/width that is a 0.1 in multiple (eg. 0.4 in by 0.4 in)

Functionality

  • Pins
    • Label pins to allow the symbol to be applied to parts in similar families
    • Name: Based on part datasheet
    • Direction: pas (passive)
    • Swap Level: 0
    • Length: middle
    • Function: none
    • Visible: both
  • Pin Placement
    • Power (VCC): top left
    • Ground (GND): bottom right
    • Inputs: left edge
    • Outputs: right edge
  • Passive Pins
    • Specifically resistors, capacitors, inductors, fuses, diodes
    • Visible: off
  • Connector Pins
    • Try to reuse an existing symbol for the size of connector
    • If need to make a new one, for pins:
      • Visible: pad
  • Decimal Labeling
    • For fractional values include the decimal point (eg. 3.3V, 4.5K)

Footprint

Grid

  • Size: 1 mm
  • Alt: 0.1 mm

Name

  • Should be manufacturer footprint name (eg. SOIC-20)

Description

  • Link to datasheet for part/family for pad layout

Style

  • Origin
    • Center origin (crosshair) on footprint center
  • Text
    • Keep text horizontal
    • Size: 1 mm
    • Ratio: 8%
    • Line Distance: 50%
    • Font: vector
  • Name
    • Locate in top left of footprint
    • Align: bottom-left
    • Layer: 25 tNames
    • Value: >NAME
  • Value
    • Locate in bottom-left of symbol
    • Align: top-left
    • Layer: 26 tValues
    • Value: >VALUE
  • Outline
    • Use Lines
      • Width: 0.2 mm
      • Style: continuous
      • Layer: 21 tPlace
    • Draw package outline per part/family datasheet
    • Used for part placement
  • Keepout
    • Use Rectangles
      • Layer: 39 tKeepout
    • Size 0.1 mm larger than the package
    • Used to prevent overlapping parts
  • Details
    • Capture more part details, extensions beyond outline, etc
    • Use
      • Width: 0.2 mm
      • Style: continuous
      • Layer: 51 tDocu

Functionality

  • Pad (Through-hole)
    • Name: name based on datasheet pin number
    • Diameter: auto
    • Drill: size based on datasheet
    • Shape: circle
    • Locked: unchecked
    • Thermals: checked
    • Stop: checked
    • First: unchecked
  • Smd (Surface Mount)
    • Name: name based on datasheet pin number
    • Smd Size: size based on datasheet
    • Layer: 1 Top (usually)
    • Roundness: 0%
    • Locked: unchecked
    • Thermals: checked
    • Stop: checked
    • Cream: checked
  • Polarity Indication
    • Through-hole
      • Make pin 1 visually different
      • Shape: square
    • Indicate polarity, when necessary
      • Prevents backwards installation
      • Direction or cathode indicators for diodes
      • Stripe or plus-minus for capacitors
    • Indicate Pin 1 for ICs
      • Use a circle (dot)
        • Width: 0 mm
        • Layer: 21 tPlace
        • Radius: 0.2 mm (at minimum)
    • Avoid overlapping pads with silkscreen, cut a section out

Device

Name

  • Should be manufacturer part number (eg. ATTINY167-SU)
  • Wildcards
    • Allows devices with multiple technologies (specifications) or packages
      • Uses wildcards in device name
      • Technology Name: *
      • Package Name: ?
    • Example
      • Regulator with two voltage (3.3V and 1.8V) technologies
        • AP2138N-3.3TRG1 for 3.3V
        • AP2138N-1.8TRG1 for 1.8V
        • Becomes AP2138N-*TRG1 with technology 3.3 and 1.8

Description

  • One sentence part function overview (valid for all variants)
  • Datasheet link

Value

  • Off unless its a passive part (resistors, capacitors, inductors, fuses, diodes)
  • If its a specific passive part with a value, add an attribute
    • Name: VALUE
    • Value: the value
    • Type: variable

Symbol

  • Use specific symbol for that part/family
  • Connectors are an exception
    • Generic symbol used for all connectors of a certain size

Footprint

  • Use specific footprint if unique
  • Try to reuse a footprint if it matches

Attribute (non-Passives)

  • Part number
    • Name: DKPN
    • Value: the Digi-Key Part Number (eg. ATTINY167-SU-ND)
    • Type: variable

Attribute (Passives)

  • Part number
    • Name: DKPN
    • Value: blank unless specific to part
    • Type: variable
  • Resistors
    • Should have tolerance and power ratings that is blank by default
    • Value is for resistance only
    • Tolerance
      • Name: Tolerance
      • Value: blank unless specific to part
      • Type: variable
    • Power
      • Name: Power
      • Value: blank unless specific to part
      • Type: variable
  • Capacitors
    • Should have tolerance and voltage ratings that is blank by default
    • Value is for capacitance only
    • Tolerance
      • Name: Tolerance
      • Value: blank unless specific to part
      • Type: variable
    • Voltage
      • Name: Voltage
      • Value: blank unless specific to part
      • Type: variable
  • Inductors
    • Should have tolerance and current ratings that is blank by default
    • Value is for inductance only
    • Tolerance
      • Name: Tolerance
      • Value: blank unless specific to part
      • Type: variable
    • Current
      • Name: Current
      • Value: blank unless specific to part
      • Type: variable
  • Fuses
    • Value is for current rating
  • Diodes
    • LEDs
      • Value should be color
    • Normal Diode
      • Value should be reverse voltage
    • TVS Diode
      • Value should be [Working Voltage]-[Breakdown Voltage] (e.g. 8V-8.5V)

Prefix

Chart for Designation
Letter Part Type
A Separate Assembly or Subassembly
C Capacitor
D Diode or LED
F Fuse
FB Ferrite bead
J Jack or Connector (least moveable connection part)
JP Jumper
K Relay or Contactor
L Inductor
LS/BZ Loudspeaker or Buzzer
M Motor
P Plug (most moveable connection part)
PS Power Supply
Q Transistor
R Resistor
RN Resistor Network
S/SW Switch
T Transformer
TP Test Point
U Integrated Circuit
X Crystal
XF External Fuse

Schematics

Grid

Sheets

Overall

Frames

Description

Nets

Style

Signals

Power

Busses

Notes

Computed Values

Specific Parts

Boards

Grid

Board Fab

Placement

General

Mechanical Considerations

Routing

General Practices

Traces

  • In general
    • Style: continuous
    • Cap: round
    • Curve: 0
  • Signals
    • Width: 0.3mm
  • Power
  • Avoid minimum sizing (based on the DRC) when possible

Via

  • At minimum
    • Diameter: 0.65mm
    • Drill: 0.35mm
    • Shape: round
    • Layer: 1-16
  • Avoid minimum sizing (based on the DRC) when possible
  • Avoid vias on signals above 1GHz
  • Use the same number of vias on differentially routed traces

Silkscreen

  • Far more important than most people realize and can take a significant amount of time to get right.
  • Makes a board easier to use, easier to debug, and harder to break.

Style

  • Text
    • Size: 1 mm (at minimum)
    • Ratio: 8% (Important text can be bolded using 15%)
    • Line Distance: 50%
    • Font: vector
    • Layer: 21 tPlace / 22 bPlace
  • Markings (anything not already in footprints)
    • Will be in final board output
    • Use Lines
      • Width: 0.2 mm
      • Style: continuous
      • Layer: 21 tPlace / 22 bPlace
  • Extra Details
    • Will not be in final board output
    • Capture more details, extensions beyond outline, etc
    • Use Lines
      • Width: 0.2 mm
      • Style: continuous
      • Layer: 51 tDocu / 52 bDocu
  • Measurements
    • Will not be in final board output
    • Useful to mark critical distances
    • Can mark outer board dimensions
    • Use Dimension
      • Size: 2 mm
      • Ratio: 8% (Important dimensions can be bolded using 15%)
      • Layer: 47 Measures
      • DType: parallel
      • Line Width: 0.2mm
      • Ext. Line Width:v auto
      • Ext. Line Length: auto
      • Ext. Line Offset: auto
      • Unit: mm
      • Precision: 3
      • Show unit: checked

Labels

  • Label all power inputs with name and voltage (current optional)
  • Label all connectors with name
  • Label all switches with position values (e.g. on or off)
  • Label all debug LEDs (e.g. MCU Status)
  • Label all fuses with current rating

General

  • Aesthetics
    • Don’t place silkscreen on vias (even tented vias) unless absolutely unavoidable
    • Have your team logo on the board (e.g. RoboBuzz)
  • Versioning
    • Have a "vMAJOR.minor" version text label on the board (e.g. v2.1)
    • Have your team name and year on the board (e.g. RoboCup 2020)
  • Board ID
    • White square to allow for a board ID (e.g. written 2 means board 2)
    • Recommended if more than three boards will be fabricated
    • Use Rectangle
      • Make width and height 5mm by 5mm (minimum)
      • Layer: 21 tPlace / 22 bPlace
Retrieved from "https://wiki.robojackets.org/index.php?title=EAGLE_Style_Guide&oldid=19499"