EAGLE Style Guide

Part Creation

Symbol

Grid

• 0.1 inches Size
• 0.01 inches Alt

Style

• Location
  • Center origin of grid on the center of the part

Font

• Font - Proportional
• Size - 0.07 in
• Value aligned bottom-left, name on top left of symbol

Functionality

• Pins should be labeled in a way that allows the symbol to be applied to any parts in a similar family
• For passive elements, pin labels can be disabled for simplicity
  • “Visible - pin” for just the pin label
  • “Visible - pad” for just the pad label
• Use passive for the pin type; at a minimum, don’t set any to power even if they are power pins
• For functional layout: Inputs on left, outputs on right, power top-left, ground bottom-right.
• Pin placement
  • Inputs on left
  • Outputs on right
  • Power on top (optional)
  • Ground on bottom (optional)
• Decimal value labeling
  • For labeling fractional values, include the decimal point. Eg. 3.3V
  • 4.51k → 4,510 kOhm
  • NOT 3V3, etc.

Footprint

Grid

• 1 mm Size
• 0.1 mm Alt

Font

• Font - Vector
• Ratio - 8%
  • unless made bold for end user benefit
• Size - 1 mm

Functionality

• Silkscreen
  • Line for alignment on tPlace/bPlace
  • All ICs should have pin one marked with a dot
  • All diodes should have direction or cathode marks
  • Clearly indicate polarity as necessary
  • Try not to overlap pads with silkscreen; although tedious, cut a section out
• Slots
  • Use the milling layer (46) to draw the outline of the slot
  • Create the pad using the elongated pad
  • Set the hole diameter to the width of the slot
  • Export the milling layer to its own gerber file and attach it with the rest of your gerbers
  • Every manufacturer has its own preferred method, but seems to be accepted widely enough

Labeling

• >NAME label on top
• >VALUE label on below
• Outline of package on tDocu/bDocu

Device

Attributes

• Name should be manufacturer part number
• Attribute - DKPN should be filled with the Digi-Key part number

Descriptions

• One sentence describes the function of the part*
• Datasheet link if available*

Prefix

• Chart for Designators

Letter	Part Type
C	Capacitor
D	Diode, LED
F	Fuse
J	Jack or Connector (least moveable connection part)
JP	Jumper
K	Relay or Contactor
L	Inductor
LS/BZ	Loudspeaker or Buzzer
M	Motor
P	Plug (most moveable connection part)
PS	Power Supply
Q	Transistor
R	Resistor
S	Switch
T	Transformer
TP	Test Point
U	Integrated Circuit
X	Crystal

Schematics

Overall

• Organize subsystems as follows:
• Related subsystems should be grouped into a sheet
• Each subsystem in a sheet should be boxed clearly, and that box labeled
  • Use line tool, width 0.006, shortdash, layer 97 info
  • Label font
    • Font - vector
    • Ratio - 12%
    • Size - 0.25 in
    • Layer - Info
  • Every sheet should have the following:
    • A frame no bigger than 11 x 17" (8½ x 11” preferred), which should have the following info:
    • A name
    • Last edit date
    • Last edit engineer(s)
    • Schematic version
    • Page #
  • Frames within a schematic should all be the same size

Nets

• Every net should have a name if possible
  • Use xref tags at 0.05 size
• Every bus should have a name and description
• Every power net should be labeled with the acceptable voltage range and max current at the net driver
• Differentially routed nets should be commented as such as the driver and sink
• Impedance controlled nets should be commented as such as the driver and sink
• Power and Ground nets
  • Use symbol with appropriate name

Configs

• Any value computed (e.g. varies by application) from a datasheet should be noted
• Any optional parts should be noted
• 0ohm isolation resistor and 0ohm jumper resistors should be noted

Boards

Fab House / Validation

• Load fab house DRC before place and route
• RoboJackets has slightly conservative DRCs for 2 and 4 layer boards

Placement

• Keep analog electronics far from high power electronics
• Locate power net status LEDs near power sources
• Provide adequate spacing for stitching/shielding if needed
• Verify any mechanical considerations
  • Board mounting holes
  • Component mounting holes/cutouts
  • Use tDoc/bDoc and/or tKeepout/bKeepout for bolt head size to prevent traces near mounting
• Place decoupling capacitors as close to the power pin of the IC as possible
  • Smallest values should be closest to pin to minimize parasitic inductance

Routing

• Avoid minimum trace width where possible
  • Suggestions: 0.2 to 0.3mm for signals, 0.4 to 0.5mm for power (increase as needed for current rating)
• Avoid minimum trace spacing where possible
• Avoid minimum drill/via size where possible
  • Suggestions: 0.35mm drill, 0.65mm diameter for vias
• Do not split differentially routed pairs unless impedance and arrival time can be matched
• Avoid vias on signals above 1GHz
• Use the same number of vias on differentially routed traces
• For two layer boards, try to keep component, signal, and power on the top layer and ground return on the bottom layer
• High frequency signals should have continuous low impedance return path directly beneath trace.
• Keep high frequency signals isolated from other signals to minimize crosstalk
• Route signals orthogonally to avoid cross-talk

Silkscreen

• This is far more important than most people realize and can take a significant amount of time to get right. A good silkscreen makes a board easier to use, easier to debug, and harder to break.

Meta

• Have at least a "vMAJOR.minor" version label on the board
• Have your team name and year (optionally month, Ubuntu style) on the board
• Have your team logo on the board
• Have a filled white square to write in an instance ID
  • Recommended if more than three boards will be fabricated
  • e.g. can say "board #2 is broken", there is a "2" written on the white square
  • Cover ink with Kapton tape
• Don’t place them on vias (even tented vias) unless absolutely unavoidable

Components & Connectors

• Set default line width to 0.2mm
• Label all power inputs with name and voltage (current optional)
• Label all connectors with name
• Label all switches with position values
• Label all debug LEDs
• Label all fuses with current rating (type optional)

Font

• All font should be vector rendered
• All font should be ratio 8%, unless made bold for end user benefit
• Component font size should be "1"
  • e.g. R45, Q1, etc.
• Layer - t/bPlace