RoboCup: Redesign 2014-2015
Contents
Phase I: Techanical Analysis
The first stage of the 2014-2015 RoboCup redesign involves brainstorming potential upgrades by researching new technologies/resources since the last revision. A parallel analysis of current robot bugs and potential enhancements is also done at this time. Outlined below is a listing of resources that the team used in this brainstorming stage.
Competition 2014 documentation
Team Description Papers (TDP)
Phase II: Design
Controlling Unit
To Do
Completed
- Obtain mbeds for robot use
Layout
To Do
- Determine location and placement for dribbler motor header
- Determine optimal placement direction for drive motor's phase connections (motor board)
- Add connection header for ball sensor to control board
- Add wires among connections in CAD assembly files
- Test motor wire modifications before working on the entire batch of motors
- Determine kicker connections and integration
Completed
- Update hall connection header to right angled one
- Add pin locations to all connection housings in CAD part files
- Update the 14-pin connection header (female) for the control-to-motor board connection
- Finalize method for adjusting motor wire lengths when motors arrive
- Determine placement of battery location
Radio
Current protocol [LINK TO BE CREATED & UPDATED]
To Do
- Determine optimal secondary frequency for base station updates
- Test methods using breakout boards and compare data rates
- Successfully communicate using two (2) nRF24L01+ transceivers and two (2) mbeds
- Research and determine best steps for structuring radio protocol with primary and seconday frequencies
- Research integration options of the CC1111 and nRF24LU1+
Completed
- Ordered 5 CC1111 transceivers as samples from TI
- Successfully communicate using two (2) CC1101 transceivers and two (2) mbeds
- Obtain breakout boards for CC1101
- Obtain breakout boards for nRF24L01+
FPGA
A few major change to the FPGA's Verilog code must be made for the 2015 redesign. This means documentation mean be produced/located for how the FPGA currently communicates on the SPI bus and append documentation for new protocol.
The Xilinx program for FPGA development (this is on ECE's virtual lab pool computers - can connect to it from anywhere): http://www.xilinx.com/products/design-tools/ise-design-suite/ise-webpack.html
| Command | Read/Write | Definition |
|---|---|---|
| 0x00 | Read Only | Receive Data Readings |
| 0x01 | Write | Set motor speeds |
| Array Index | Bit(s) | Definition |
|---|---|---|
| 0 | 7..0 | FPGA Version (0x04 in 2014) |
| 1 | 7..0 | Encoder 1 Count (LSB) |
| 2 | 7..0 |
Encoder 1 Count (MSB) |
| 3 | 7..0 |
Encoder 2 Count (LSB) |
| 4 | 7..0 |
Encoder 2 Count (MSB) |
| 5 | 7..0 |
Encoder 3 Count (LSB) |
| 6 | 7..0 |
Encoder 3 Count (MSB) |
| 7 | 7..0 |
Encoder 4 Count (LSB) |
| 8 | 7..0 |
Encoder 4 Count (MSB) |
| 9 | 7..0 |
Motor Fault |
| 10 | 7..0 |
Kicker Status |
| 11 | 7..0 |
Kicker Voltage |
| 12 | 7..0 |
Hall Count 1 |
| 13 | 7..0 |
Hall Count 2 |
| 14 | 7..0 |
Hall Count 3 |
| 15 | 7..0 | Hall Count 4 |
| 16 | 7..0 |
Hall Count 5 |
| Array Index | Bit(s) | Definition |
|---|---|---|
| 0 | 7..0 | Packet Type (0x01) |
| 1 | 7..0 | Motor 1 Speed (LSB) |
| 2 | 7..4 |
Reserved (Always 0) |
| 3..2 | Motor 1 Drive Mode | |
| 1..0 | Motor 1 Speed (MSB) | |
| 3 | 7..0 | Motor 2 Speed (LSB) |
| 4 | 7..4 | Reserved (Always 0) |
| 3..2 | Motor 2 Drive Mode | |
| 1..0 | Motor 2 Speed (MSB) | |
| 5 | 7..0 | Motor 3 Speed (LSB) |
| 6 | 7..4 | Reserved (Always 0) |
| 3..2 | Motor 3 Drive Mode | |
| 1..0 | Motor 3 Speed (MSB) | |
| 7 | 7..0 | Motor 4 Speed (LSB) |
| 8 | 7..4 | Reserved (Always 0) |
| 3..2 | Motor 4 Drive Mode | |
| 0..1 | Motor 4 Speed (MSB) | |
| 9 | 7..0 | Dribbler Motor Speed (LSB) |
| 10 | 7 | Kicker Charge |
| 6 | Chipper Enable (1=Chip, 0=Kick) | |
| 5..4 | Reserved (Always 0) | |
| 3..2 | Dribbler Motor Drive Mode | |
| 1..0 | Dribbler Motor Speed (MSB) | |
| 11 | 7..0 | style="text- |
To Do
- Transition the I2C bus lines to the microcontroller
- Update Verilog for new balanced encoder signals (A+, A-, B+, B-)
- ( (A+) + (A-) == 0 ) should be true for no errors
Completed
- Determine what communications occur over the SPI bus
- Finalized that the 2015 motor will use the current FPGA
Motors
Maxon 50W Custom Motor Drawing
To Do
- Order motor controller boards
- Test different circuits and document data result set to wiki
Completed
- Ordered 3 DRV8301 Pre-Drivers from TI
- Finalized the protyping designs of single motor controllers
- Ordered motors
Motion Sensing
To Do
- Integrate the MPU-9250 into the I2C data bus lines from the mbed
Completed
- Order breakout board for MPU-9250
Error Detection & Indication
To Do
- Determine best solution for controlling the WS2812B RGB LED
Completed
- Create breakout board for MCP23017 and place on GitHub repo (robocup-pcb)
Battery & Power
The following contains a listing of batteries that were considered for the 2015 design along with other battery/power adapters and accessories.
Battery
Zippy Flightmax 2200mAh 5S 40C
Connector
Charging Lead
Balancing Board
All Batteries
Zippy Flightmax 2500mAh 5S 20C
Zippy Flightmax 1800mAh 5S 40C
Phase III: Production
The final phase for creating the new fleet of robots involves outlining the steps and procedures for robot manufacturing and assebly. Future members can use this area as a reference for the fleet's required maintenance. It may also be benefitial for strengthening tolerances in future fleet builds.
Electronics Assembly
https://learn.sparkfun.com/tutorials/electronics-assembly
http://www.soldermask.com/ <- Sparfun uses these guys for all their solder stencils
