Difference between revisions of "RC11-Assembly Instructions"

From RoboJackets Wiki
Jump to navigation Jump to search
m (recategorizing)
Line 13: Line 13:
 
<br>
 
<br>
 
<br>
 
<br>
Parts: Bearings, Chipper Arms, 1/Pins, Kicker Boot,  Inch 6-32 Socket Cap Screws, front solenoid mount (L-block)
+
Parts: Bearings, Chipper Arms, 1/16� Pins, Kicker Boot,  Inch 6-32 Socket Cap Screws, front solenoid mount (L-block)
 
<br>
 
<br>
 
<br>
 
<br>
Line 24: Line 24:
 
'''Kicker-Chipper Assembly with Bottom Plate and Dribbler'''
 
'''Kicker-Chipper Assembly with Bottom Plate and Dribbler'''
 
<br><br>
 
<br><br>
Parts: Kicker plunger, bobbin, rear solenoid mount, center solenoid mount, kicker spring, chipper arm assembly, (, 3/8, and 5/8 inch) 6-32 Socket Cap Screws, dribbler assembly, chipper solenoid, 12-screws
+
Parts: Kicker plunger, bobbin, rear solenoid mount, center solenoid mount, kicker spring, chipper arm assembly, (, 3/8, and 5/8 inch) 6-32 Socket Cap Screws, dribbler assembly, chipper solenoid, 12-24� screws
 
<br><br>
 
<br><br>
 
1. Take kicker plunger assembly with kicker boot removed a d insert spring into plunger, with small end of spring facing kicker plunger plate<br>
 
1. Take kicker plunger assembly with kicker boot removed a d insert spring into plunger, with small end of spring facing kicker plunger plate<br>
Line 30: Line 30:
 
3. Place bobbin onto kicker plunger and insert into center solenoid mount<br>
 
3. Place bobbin onto kicker plunger and insert into center solenoid mount<br>
 
4. Place chipper arm assembly onto front of bobbin and insert plunger through L-Block<br>
 
4. Place chipper arm assembly onto front of bobbin and insert plunger through L-Block<br>
5. Attach kicker boot to plunger with 3/6-32 Socket Cap Screw<br>
+
5. Attach kicker boot to plunger with 3/8� 6-32 Socket Cap Screw<br>
 
6. Place chipper solenoid into center solenoid mount and screw on solenoid nut<br>
 
6. Place chipper solenoid into center solenoid mount and screw on solenoid nut<br>
 
7. Place rear solenoid mount onto back of chipper solenoid with wire coming out on right side and fasten rear solenoid mount to center solenoid mount with 12-24 screws-'''Do not tighten'''.<br>
 
7. Place rear solenoid mount onto back of chipper solenoid with wire coming out on right side and fasten rear solenoid mount to center solenoid mount with 12-24 screws-'''Do not tighten'''.<br>
 
8. Place chipper plunger into chipper solenoid<br>
 
8. Place chipper plunger into chipper solenoid<br>
9. Attach dribbler and kicker-chipper assembly to bottom plate, but screw the screws in only about to of their full depth<br>
+
9. Attach dribbler and kicker-chipper assembly to bottom plate, but screw the screws in only about to of their full depth<br>
 
10. Take rubber band on dribbler and wrap around chipper plunger bar while inserting the bar int o the chipper arm slots.<br>
 
10. Take rubber band on dribbler and wrap around chipper plunger bar while inserting the bar int o the chipper arm slots.<br>
 
11. Tighten all screws fully into the bottom of the chipper-kicker assembly and dribbler assembly<br>
 
11. Tighten all screws fully into the bottom of the chipper-kicker assembly and dribbler assembly<br>
Line 45: Line 45:
 
'''Electronics Stack Assembly'''
 
'''Electronics Stack Assembly'''
 
<br><br>
 
<br><br>
Parts: Kicker Board, Electronics Board, standoffs top plate, 1/6-32 Socket Cap Screw
+
Parts: Kicker Board, Electronics Board, standoffs top plate, 1/4� 6-32 Socket Cap Screw
 
<br><br>
 
<br><br>
 
1. Attach electronics board and kicker board together with standoffs. And then attach to top plate.<br>
 
1. Attach electronics board and kicker board together with standoffs. And then attach to top plate.<br>
Line 55: Line 55:
 
[[Category: RoboCup]]
 
[[Category: RoboCup]]
 
[[Category: Mechanical]]
 
[[Category: Mechanical]]
[[Category: Year: 2010-2011]]
+
[[Category: 2010-2011]]

Revision as of 22:28, 13 June 2018

The following is a rough guideline for assembly of the robot. It largely contains steps for assembly of major mechanical components. Expansion of these steps could include:
- Drive Module Assembly
- Dribbler Assembly
- Electrical Board Integration and Wiring
- Renderings and Diagrams

Robot assembly integration should follow order shown here.


Chipper Arm Assembly

Parts: Bearings, Chipper Arms, 1/16� Pins, Kicker Boot, � Inch 6-32 Socket Cap Screws, front solenoid mount (L-block)

1. Attach bearing to arm with pin, using press
2. Place arm onto boot and press pin into both from outside face of arm
3. Press bearing onto other arm
4. Place arms with bearings onto sides of L-Block and press pin into second arm and boot
5. Screw arms and boot together using green or blue Locktite.

Kicker-Chipper Assembly with Bottom Plate and Dribbler

Parts: Kicker plunger, bobbin, rear solenoid mount, center solenoid mount, kicker spring, chipper arm assembly, (�, 3/8, and 5/8 inch) 6-32 Socket Cap Screws, dribbler assembly, chipper solenoid, 12-24� screws

1. Take kicker plunger assembly with kicker boot removed a d insert spring into plunger, with small end of spring facing kicker plunger plate
2. Insert plunger through back of lower hole of the center solenoid mount
3. Place bobbin onto kicker plunger and insert into center solenoid mount
4. Place chipper arm assembly onto front of bobbin and insert plunger through L-Block
5. Attach kicker boot to plunger with 3/8� 6-32 Socket Cap Screw
6. Place chipper solenoid into center solenoid mount and screw on solenoid nut
7. Place rear solenoid mount onto back of chipper solenoid with wire coming out on right side and fasten rear solenoid mount to center solenoid mount with 12-24 screws-Do not tighten.
8. Place chipper plunger into chipper solenoid
9. Attach dribbler and kicker-chipper assembly to bottom plate, but screw the screws in only about � to � of their full depth
10. Take rubber band on dribbler and wrap around chipper plunger bar while inserting the bar int o the chipper arm slots.
11. Tighten all screws fully into the bottom of the chipper-kicker assembly and dribbler assembly
12. Tighten 12-24 screws that connect center solenoid mount to rear solenoid mount

Wheel Module Integration

1. Screw wheel modules into bottom plate while having motor and encoder wires facing towards the pitch axis (lateral center-line) of robot

Electronics Stack Assembly

Parts: Kicker Board, Electronics Board, standoffs top plate, 1/4� 6-32 Socket Cap Screw

1. Attach electronics board and kicker board together with standoffs. And then attach to top plate.
2. Attach top plate to tops of drive motors modules
3. Attach standoffs for shell