Difference between revisions of "RoboCup: Control Board 2011"
| Line 25: | Line 25: | ||
=== MOSFET Operation === | === MOSFET Operation === | ||
| − | [[File:RC EE Mosfet Diagram.png|thumb|right|400px | + | [[File:RC EE Mosfet Diagram.png|thumb|right|400px]] |
A MOSFET or Metal-Oxide-Semiconductor Field-Effect Transistor, is basically a switch. There are 3 terminals: source, drain, and gate, and [[:File:RC EE Mosfet Diagram.png|figure 2]] outlines the physical layout of their relations. If you apply a voltage at the gate, this will allow a flow of charges from the source to the drain. These devices use metal oxides and the charges flow due to the effect of an electric field between the source and drain. Hence why they are called MOSFET. There are 2 types of MOSFETs, nMOSFET - where the majority of charge carriers are electrons - and pMOSFET - where the majority of charge carriers are holes. The gate-source voltage must be high (positive) to turn on a nMOS and low (negative) to turn on a pMOS. This voltage is refereed to as the threshold voltage and is defined in table 1 below. The pMOS is better at pulling the output high while nMOS is better at pulling the output low; Therefore, both MOSFETs are used in the motor driver circuit - they complement one another. | A MOSFET or Metal-Oxide-Semiconductor Field-Effect Transistor, is basically a switch. There are 3 terminals: source, drain, and gate, and [[:File:RC EE Mosfet Diagram.png|figure 2]] outlines the physical layout of their relations. If you apply a voltage at the gate, this will allow a flow of charges from the source to the drain. These devices use metal oxides and the charges flow due to the effect of an electric field between the source and drain. Hence why they are called MOSFET. There are 2 types of MOSFETs, nMOSFET - where the majority of charge carriers are electrons - and pMOSFET - where the majority of charge carriers are holes. The gate-source voltage must be high (positive) to turn on a nMOS and low (negative) to turn on a pMOS. This voltage is refereed to as the threshold voltage and is defined in table 1 below. The pMOS is better at pulling the output high while nMOS is better at pulling the output low; Therefore, both MOSFETs are used in the motor driver circuit - they complement one another. | ||
| − | {| class="wikitable" style="width: 350px;" | + | {| class="wikitable" style="width: 350px;" align="center" |
|- | |- | ||
! nMOS | ! nMOS | ||
Revision as of 00:20, 5 January 2015
| Timeline | |
|---|---|
| Year | 2013 |
| Versions | |
| Control Board | 2011 Rev c |
| Kicker Board | - |
| Main Components | |
| MCU | AT91SAM7S256 |
| FPGA | - |
| IMU | - |
| Motors | Maxon EC45flat 30W |
| Battery | - |
Contents
Overview
This page contains reference information for the 2011c control boards.
Quick Links
Motor Operations
A three-phase bridge (figure 1) is the name of the circuit that is used to control each motor. The control signals for the motors come from the FPGA (XC3S100E). The robot uses 4 30W three phase brushless motors to maneuver itself on the field. A 5th motor is also used for the dribbler. In order to operate each motor with the needed precision, a brushless motor driving circuit is used for every motor. The motors also contain hall--channel MOSFET (IRF9310TRPBF) is used to connect to +12V and a n-
MOSFET Operation
A MOSFET or Metal-Oxide-Semiconductor Field-Effect Transistor, is basically a switch. There are 3 terminals: source, drain, and gate, and figure 2 outlines the physical layout of their relations. If you apply a voltage at the gate, this will allow a flow of charges from the source to the drain. These devices use metal oxides and the charges flow due to the effect of an electric field between the source and drain. Hence why they are called MOSFET. There are 2 types of MOSFETs, nMOSFET - where the majority of charge carriers are electrons - and pMOSFET - where the majority of charge carriers are holes. The gate-source voltage must be high (positive) to turn on a nMOS and low (negative) to turn on a pMOS. This voltage is refereed to as the threshold voltage and is defined in table 1 below. The pMOS is better at pulling the output high while nMOS is better at pulling the output low; Therefore, both MOSFETs are used in the motor driver circuit - they complement one another.
| nMOS | pMOS |
|---|---|
| Vg - Vs > Vt | Vg - Vs < Vt |
Single Motor Winding Circuit Explanation
From figure 3, OUTA is the inverting output and OUTB is non--down resistors that ensure INA and INB maintain a proper value if there is no signal from the FPGA. R54 and R55 provide signal stability for the base of each FET (the voltage could oscillate back and forth without them). C26 is used to filter out unwanted high frequencies from VDD.
Debugging
If a fuse is blown, then a likely cause is that one of the FETs experienced a high back flow of current and broke. Ideally you should test for faulty FETs with the FET tester. If you are stranded on a deserted island without the FET tester, you can still determine if a FET is faulty or not. The steps for checking both nFETs and pFETs using a digital multimeter are outlined on the testing a MOSFET page. It is recommended to change the entire three-phase bridge (3 pFETs, 3 nFETs and 3 MOSFET drivers) if any 1 part is damaged.
Other Websites/Resources
- Youtube video explaining the operations of brushless DC motors (BLDC) - [1]
- PDF about more BLDC motors - [2]
Power Operations
This is the main stage where the input, VDD, from the battery is converted to the different DC voltage levels required by the various components on the board. To protect the components on the board, two (2) things are done:
- The kicker's power supply is separated from the rest of the control board.
- A fuse is used for the kicker power supply and the power supply for the motors.
The big red,10A, fuse is used for connecting the battery to all of the motors and the kicker board. The 10A fuse is independent from all digital logic power.
Voltage Monitor for kicker
The voltage monitor is a circuit used to measure the voltage at the output of the transformers, since they are in the range of 150V and is a cause of concern for safety if it is exceeded. The main component of the voltage monitor is the analog-to-digital converter, ADC081C027. The type of architecture used in the ADC is an 8-bit Successive Approximation Register (SAR). In successive approximation, the ADC internally has a DAC, a comparator and 8-
LM2734 Switching Voltage Regulator
The LM2734 is a voltage converter that can convert a maximum of 24V to different output voltages depending upon its configuration in a circuit using external resistors, capacitors, inductors, and diodes. The circuit used to convert VDD to 5V is based on a similar circuit provided in the datasheet. The output voltage depends on the values of the resistors R83 and R84 at the feedback (FB) pin. From the reference diagram, the way to calculate output voltage is given by, R1 = R2 ( VO / Vref - 1 ). Usually, R2 is fixed as 10kohm. We need VO to be 5V. Vref is set internally in the IC as 0.8V, so R1 is calculated to be 52.5kohm and the control board reflects these values.
MCP1824 Linear Voltage Regulator
The MCP1824is the name for a series of LDO voltage regulatorsthat are capable of providing up to 300mA of current. The regulators come in various fixed and adjustable voltages when purchasing. The control board contains three (3) of these MCP1824regulators. All regulators on the control board from this series are the kind that produce a fixed voltage. These voltages are listed below and test points are located to the left of the power switch for easily probing the outputs of these regulators.
- 3.3V
- 2.5V
- 1.2V
Radio Operations
| Halo Antenna |
Images of Control Board
Back
Motor FETs
Motor FETs
Single Motor Circuit
Motor FETs
Motor FETs
System Clock
Top
Top
Connectors
Connectors
Power Switch
Connectors
Left View
Right View
Connectors
Kicker Discharge Button
Robot ID Select
Robot ID Select
Left Angled View
Side View
Status LEDs
Power Switch
Encoder & Kicker Connectors
Motor & Encoder Connectors
Power Inductor
Kicker Power Connector
Power Circuits
Selectable Switches
Xilinx FPGA
Board ID Location
USB Connection
Atmel Microcontroller
Accelerator/Gyroscope Sensors
Reset Button
USB & Antenna Connections
Board Overview Videos
| Board Overview | |
| FPGA |
Component List
