Difference between revisions of "RC09-Dribbler"
(→Motor Gear (Supplier B)) |
(→Output Gear (Supplier B)) |
||
| Line 52: | Line 52: | ||
====Output Gear (Supplier B)==== | ====Output Gear (Supplier B)==== | ||
:Vendor: WM Berg | :Vendor: WM Berg | ||
| − | :Part No.: PFS80- | + | :Part No.: PFS80-26 |
| − | :Description: Module 0.5, 20 Teeth, 20° Pressure Angle, Stainless Steel Gear with set screw, 3mm bore, | + | :Description: Module 0.5, 20 Teeth, 20° Pressure Angle, Stainless Steel Gear with set screw, 3mm bore, 13mm PD |
| − | :Cost: $ | + | :Cost: $17.42 |
:Drawing:[http://www.wmberg.com/catalog/catpage.aspx?url=pdf/M05B082.pdf Dribbler Gear Spec Sheet] | :Drawing:[http://www.wmberg.com/catalog/catpage.aspx?url=pdf/M05B082.pdf Dribbler Gear Spec Sheet] | ||
| − | |||
| − | |||
===Stock=== | ===Stock=== | ||
Revision as of 21:16, 18 March 2009
Contents
Testing
Dribbler Bar Type
The current plan for the 2009 Dribbler is to have it be segmented. Segmenting creates two sections of dribbler with a gap in between. Theoretically, this allows for more ball control. The Mexican team used this set up in 2008 (see here). The gap in between is going to be between a quarter to a third of the length of the dribbler.
Performance Assessment
To measure last years performance and game play. This will be determined by receiving a kick and grabbing a stationary ball all under computer control. These results will be used as a benchmark to our new Dribbler model.
Pouring
We might want to look into pouring a mold of silicon rubber for the Dribbler assembly. This will be easier to put the rubber on the shaft. We don't know how well this will work, but we should do tests to see its effectiveness.
Candidates
- 75115A65 McMaster-Carr ($17.89)
Obstacles
- Make an outer mold.
- Make inner mold/shaft.
- Develop out gassing technique for pour.
Parts & Components
Motors
Dribbler Motor
- Vendor - Maxon
- Part No. - 266521 (with attached gear head 118184)
- 5.4 gear reduction
- Cost - $146.20 each
- Notes
Gearing
Motor Gear (Supplier A)
- Vendor: SDP/SI
- Part No.: S10T05M034S0303
- Description: Module 0.5, 34 Teeth, 20° Pressure Angle, Stainless Steel 303 Gear with hub set screw, 3mm bore, 17mm PD
- Cost: $12.56
- Drawing:Motor Gear Spec Sheet
- Roller gear bore must be reamed out to 4mm
Motor Gear (Supplier B)
- Vendor: WM Berg
- Part No.: PFS80-34
- Description: Module 0.5, 34 Teeth, 20° Pressure Angle, Stainless Steel Gear with hub set screw, 3mm bore, 17mm PD
- Cost: $18.73
- Drawing:Motor Gear Spec Sheet
- Roller gear bore must be reamed out to 4mm
Output Gear (Supplier A)
- Vendor: SDP/SI
- Part No.: S10T05M020S0303
- Description: Module 0.5, 20 Teeth, 20° Pressure Angle, Stainless Steel 303 Gear with set screw, 3mm bore, 10mm PD
- Cost: $10.46
- Drawing:Dribbler Gear Spec Sheet
- Roller gear bore must be reamed out to 4mm
- Powers the dribbler roller - is recessed into the roller itself
Output Gear (Supplier B)
- Vendor: WM Berg
- Part No.: PFS80-26
- Description: Module 0.5, 20 Teeth, 20° Pressure Angle, Stainless Steel Gear with set screw, 3mm bore, 13mm PD
- Cost: $17.42
- Drawing:Dribbler Gear Spec Sheet
Stock
RTV
- Vendor: McMaster-Carr
- Part No.: 75115A65
- Description: Loctite Gray Silicone Gasket Maker Number 18718, 2.36 Ounce Tube
- Cost: $17.89
Shaft
- Vendor: McMaster-Carr
- Part No.: 8974K25
- Description: Multipurpose Aluminum (Alloy 6061) 7/16" Diameter X 6' Length
- Cost: $13.51
Fasteners
Action Log
- 10/12/2008 - Segmented dribbler prototype design completed.
- 10/16/2008 - Acquisition of silicone gasket sealer to test in mold.
- 11/02/2008 - The spare dribbler from 08 was modified to be a segmented.
- Note - The rubber as damaged some while on the lathe. Patched was tested with gasket sealer.
- 11/09/2008 - Impact tester was modified to allow for testing of receiving a pass.
