Difference between revisions of "RC08Brushless"
Jump to navigation
Jump to search
| Line 37: | Line 37: | ||
* NMOS and a PMOS | * NMOS and a PMOS | ||
* The FETS have to be able to handle 10A drain current | * The FETS have to be able to handle 10A drain current | ||
| − | * | + | * [[RC08MotorFETS | Matrix of Potential FETS]] Other FETs we considered |
| + | |||
| + | ==Schematics== | ||
| + | Schematics | ||
| + | ==Parts== | ||
| + | We are performing commutation on the FPGA with gate drivers. | ||
| + | |||
| + | ====FETS==== | ||
{| style="text-align:center;" cellspacing ="0" cellpadding="1" | {| style="text-align:center;" cellspacing ="0" cellpadding="1" | ||
| Line 72: | Line 79: | ||
| style="border:0.5px solid black; border-bottom=0px; background:white;" | [http://www.onsemi.com/pub/Collateral/NTMS10P02R2-D.PDF] | | style="border:0.5px solid black; border-bottom=0px; background:white;" | [http://www.onsemi.com/pub/Collateral/NTMS10P02R2-D.PDF] | ||
|} | |} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Articles== | ==Articles== | ||
Revision as of 15:13, 18 November 2007
In 2008 RoboCup switched to brushless DC motors. While brushless motors are smaller and far more efficient than brushed motors the commutation normally performed inside a brushed DC motor will need to be done externally using some control circuitry. There are two main parts to our brushless motor controller solution; the controller which uses sensors on the motor to gate signals to one of three coils, and the half-bridge motor drivers which actually drive the coils.For the controller a special-purpose brushless motor driver IC was used. For information on the motors or motor control software please see their respective pages.
Contents
Motor Frequency Analysis
Tasks
- [ ] Get the motor and begin playing with it
- [X] Call Maxon and get a recommendation on motor drivers (They spec parts not sure which drivers they use)
- [X] Figure out max current draw. (10A starting current)
- [ ] Develope Model of Motor and get Frequency Response
- [ ] Find and purchase Flat Flex Cable (FFC) connectors
- [ ] Purchase large mosfets for testing
- [ ] Purchase Surfboard for mounting DSC
- [ ] Build test rig
- [ ] Finalize on a DSC
- [ ] Choose MOSFETS
- [ ] Sample all the parts
- [ ] Schematic Design
- [ ] Build prototype
- [ ] Prototype evaluation
- [ ] Make necessary changes
Specifications
Motor Controller Chip
- The motor is spec'd at 12V and is 30W
- A decent transient response (dead-time + switching time)
- 3-Channels in one package
- Braking is not a requirement but would be nice
- High Impedance OFF state
- Fault protection (overvoltage, overcurrent, fast response)
- Small package
- Ability to operate in the >20kHz range
- Gate drive capability (either can directly driver the gate or is open drain.)
- Data sheet recommends a MOSFET
- Matrix of Potential Drivers
MOSFET
- NMOS and a PMOS
- The FETS have to be able to handle 10A drain current
- Matrix of Potential FETS Other FETs we considered
Schematics
Schematics
Parts
We are performing commutation on the FPGA with gate drivers.
FETS
| Part No. | Make | Package | ContIDS | MaxIDS | Rds | MaxVGS | Samples | Data Sheet |
|---|---|---|---|---|---|---|---|---|
| NTMS4503N N-Channel | ON Semi | SO-8 | 14 A | -- | -- | 28 V | Y | [1] |
| NTMS10P02 P-Channel | ON Semi | SO-8 | 10 A | -- | -- | 20 V | Y | [2] |
Articles
Modeling a DC motor Brush-Less Motor Simulink
Links
