Difference between revisions of "WakiSmaki"

From RoboJackets Wiki
Jump to navigation Jump to search
(Changes/Improvements)
(WakiSmaki)
 
(3 intermediate revisions by 2 users not shown)
Line 37: Line 37:
 
*Results: 0/2
 
*Results: 0/2
 
**Bracket Style: Double Elimination
 
**Bracket Style: Double Elimination
***[(Video Link) loss vs Deadeight (Drum Kitbot)]
+
***[https://youtu.be/jfENAwaXAu8 loss vs Deadeight (Drum Kitbot)]
 
****Vertical hit took off the ring
 
****Vertical hit took off the ring
 
****All Nylon flywheels came off their flanges by coming off diagonally
 
****All Nylon flywheels came off their flanges by coming off diagonally
 
****Bot we lost to: http://www.teamrollingthunder.com/Kitbots/3lb_Kits/Weta_2/body_weta_2.html
 
****Bot we lost to: http://www.teamrollingthunder.com/Kitbots/3lb_Kits/Weta_2/body_weta_2.html
***[(Video Link) loss vs Mux]
+
***[https://youtu.be/M5PLtmMmN7s loss vs Mux]
 
****Took a couple hits to the ring before it came off
 
****Took a couple hits to the ring before it came off
 
****Flywheels failed again
 
****Flywheels failed again
Line 90: Line 90:
 
* Did not take any damage when spinning properly
 
* Did not take any damage when spinning properly
 
* Actually spun up
 
* Actually spun up
 +
* Drive worked and never took any damage
  
 
==== Changes/Improvements ====
 
==== Changes/Improvements ====
Line 96: Line 97:
 
* Make weapon drive wheel out of a hard rubber. DO NOT USE SILICONE
 
* Make weapon drive wheel out of a hard rubber. DO NOT USE SILICONE
 
* Use more plastic on low stress components
 
* Use more plastic on low stress components
 +
* You can buy urethane coated bearings. We probably would have used that if we knew.
 +
 +
=== WakiiSmakii ===
 +
 +
Broke before it could compete.
 +
 +
==== Changes Made ====
 +
 +
* New Flywheel design with thrust bearings to hold flywheels from above
 +
* New Tooth design
 +
* New top and bottom plates
 +
 +
==== Problems ====
 +
 +
* Electronics needed to be held more strongly.
  
 
== Notes: ==
 
== Notes: ==

Latest revision as of 20:59, 4 April 2019

WakiSmaki
WakiSmaki
Year Of Creation 2018-2019
Versions
Current Version 1.0
Wins/Losses 0/2
Information and Statistics
Weight Class BeetleWeight
Weapon Class Ring Spinner
Combined Wins/Losses 0/2

WakiSmaki is a 3lb ring spinner which features a simple flywheel design with 5 flywheels. It had a direct drive with a wheel attached to a motor that drove the two part ring. The ring had an interior channel that the weapon drive and flywheels resided in.

Competitions

Motorama 2019

Versions

WakiSmaki

Created by: Dylan Fife, Brian Epstein, Zachary Ghezzi, Andrew Teske

Drive Motors DYS BE1806 2300KV Motors
Drive Motor Gearboxes KITBOTS 1000rpm Gearmotor Gearboxes
Drive Motor Controllers DYS 20A Micro Opto Multi-rotor ESC
Weapon Motor PROPDRIVE v2 2836 3000KV Brushless Outrunner Motor
Weapon Motor Controllers TURNIGY Plush 60amp Speed Controller w/BEC
Receiver Turnigy T6A-V2 AFHDS 2.4GHz 6Ch Receiver V2
Remote Control Turnigy T6A-V2 AFHDS 2.4GHz 6Ch Transmitter V2
Battery Turnigy Nano-Tech 1000mAh 3s 45~90c LiPo Pack

Problems

  • Flywheels came off because they were held in with a press fit and a flange
  • Weapon drive wheel ballooned and went over the cap that was supposed to hold it in
  • Lower RPM compared to drums makes it so that it gets hit first
  • Because our orders went out of stock (VEX) we had to redesign last minute and went overweight
  • We should have done weight savings on anything we could have

Good aspects

  • Did not take any damage when spinning properly
  • Actually spun up
  • Drive worked and never took any damage

Changes/Improvements

  • Retain flywheels better
  • Make weapon drive wheel out of a hard rubber. DO NOT USE SILICONE
  • Use more plastic on low stress components
  • You can buy urethane coated bearings. We probably would have used that if we knew.

WakiiSmakii

Broke before it could compete.

Changes Made

  • New Flywheel design with thrust bearings to hold flywheels from above
  • New Tooth design
  • New top and bottom plates

Problems

  • Electronics needed to be held more strongly.

Notes:

(random joke, optional)

(Naming inspiration, optional)

(Names of original builders)