EAGLE Style Guide

From RoboJackets Wiki
Revision as of 13:40, 22 April 2020 by Jspall3 (talk | contribs) (Symbol)
Jump to navigation Jump to search

Part Creation

Symbol

Grid

  • 0.1 inches Size
  • 0.01 inches Alt

Style

  • Location
    • Center origin of grid on the center of the part
    • Value tag aligned bottom-left
    • Name tag aligned top-left

Font

  • Font - Proportional
  • Size - 0.07 in

Functionality

  • Pins should be labeled in a way that allows the symbol to be applied to any parts in a similar family
  • For passive elements, pin labels can be disabled for simplicity
    • “Visible - pin” for just the pin label
    • “Visible - pad” for just the pad label
  • Use passive for the pin type; at a minimum, don’t set any to power even if they are power pins
  • For functional layout: Inputs on left, outputs on right, power top-left, ground bottom-right.
  • Pin placement
    • Inputs on left
    • Outputs on right
    • Power on top (optional)
    • Ground on bottom (optional)
  • Decimal value labeling
    • For labeling fractional values, include the decimal point. Eg. 3.3V
    • 4.51k → 4,510 kOhm
    • NOT 3V3, etc.

Footprint

Grid

  • 1 mm Size
  • 0.1 mm Alt

Font

  • Font - Vector
  • Ratio - 8%
    • unless made bold for end user benefit
  • Size - 1 mm

Functionality

  • Silkscreen
    • Line for alignment on tPlace/bPlace
    • All ICs should have pin one marked with a dot
    • All diodes should have direction or cathode marks
    • Clearly indicate polarity as necessary
    • Try not to overlap pads with silkscreen; although tedious, cut a section out
  • Slots
    • Use the milling layer (46) to draw the outline of the slot
    • Create the pad using the elongated pad
    • Set the hole diameter to the width of the slot
    • Export the milling layer to its own gerber file and attach it with the rest of your gerbers
    • Every manufacturer has its own preferred method, but seems to be accepted widely enough

Labeling

  • >NAME label on top
  • >VALUE label on below
  • Outline of package on tDocu/bDocu

Device

Attributes

  • Name should be manufacturer part number
  • Attribute - DKPN should be filled with the Digi-Key part number

Descriptions

  • One sentence describes the function of the part*
  • Datasheet link if available*

Prefix

  • Chart for Designators
Letter Part Type
C Capacitor
D Diode, LED
F Fuse
J Jack or Connector (least moveable connection part)
JP Jumper
K Relay or Contactor
L Inductor
LS/BZ Loudspeaker or Buzzer
M Motor
P Plug (most moveable connection part)
PS Power Supply
Q Transistor
R Resistor
S Switch
T Transformer
TP Test Point
U Integrated Circuit
X Crystal

Schematics

Overall

  • Organize subsystems as follows:
  • Related subsystems should be grouped into a sheet
  • Each subsystem in a sheet should be boxed clearly, and that box labeled
    • Use line tool, width 0.006, shortdash, layer 97 info
    • Label font
      • Font - vector
      • Ratio - 12%
      • Size - 0.25 in
      • Layer - Info
    • Every sheet should have the following:
      • A frame no bigger than 11 x 17" (8½ x 11” preferred), which should have the following info:
      • A name
      • Last edit date
      • Last edit engineer(s)
      • Schematic version
      • Page #
    • Frames within a schematic should all be the same size

Nets

  • Every net should have a name if possible
    • Use xref tags at 0.05 size
  • Every bus should have a name and description
  • Every power net should be labeled with the acceptable voltage range and max current at the net driver
  • Differentially routed nets should be commented as such as the driver and sink
  • Impedance controlled nets should be commented as such as the driver and sink
  • Power and Ground nets
    • Use symbol with appropriate name

Configs

  • Any value computed (e.g. varies by application) from a datasheet should be noted
  • Any optional parts should be noted
  • 0ohm isolation resistor and 0ohm jumper resistors should be noted

Boards

Fab House / Validation

  • Load fab house DRC before place and route
  • RoboJackets has slightly conservative DRCs for 2 and 4 layer boards

Placement

  • Keep analog electronics far from high power electronics
  • Locate power net status LEDs near power sources
  • Provide adequate spacing for stitching/shielding if needed
  • Verify any mechanical considerations
    • Board mounting holes
    • Component mounting holes/cutouts
    • Use tDoc/bDoc and/or tKeepout/bKeepout for bolt head size to prevent traces near mounting
  • Place decoupling capacitors as close to the power pin of the IC as possible
    • Smallest values should be closest to pin to minimize parasitic inductance

Routing

  • Avoid minimum trace width where possible
    • Suggestions: 0.2 to 0.3mm for signals, 0.4 to 0.5mm for power (increase as needed for current rating)
  • Avoid minimum trace spacing where possible
  • Avoid minimum drill/via size where possible
    • Suggestions: 0.35mm drill, 0.65mm diameter for vias
  • Do not split differentially routed pairs unless impedance and arrival time can be matched
  • Avoid vias on signals above 1GHz
  • Use the same number of vias on differentially routed traces
  • For two layer boards, try to keep component, signal, and power on the top layer and ground return on the bottom layer
  • High frequency signals should have continuous low impedance return path directly beneath trace.
  • Keep high frequency signals isolated from other signals to minimize crosstalk
  • Route signals orthogonally to avoid cross-talk

Silkscreen

  • This is far more important than most people realize and can take a significant amount of time to get right. A good silkscreen makes a board easier to use, easier to debug, and harder to break.

Meta

  • Have at least a "vMAJOR.minor" version label on the board
  • Have your team name and year (optionally month, Ubuntu style) on the board
  • Have your team logo on the board
  • Have a filled white square to write in an instance ID
    • Recommended if more than three boards will be fabricated
    • e.g. can say "board #2 is broken", there is a "2" written on the white square
    • Cover ink with Kapton tape
  • Don’t place them on vias (even tented vias) unless absolutely unavoidable

Components & Connectors

  • Set default line width to 0.2mm
  • Label all power inputs with name and voltage (current optional)
  • Label all connectors with name
  • Label all switches with position values
  • Label all debug LEDs
  • Label all fuses with current rating (type optional)

Font

  • All font should be vector rendered
  • All font should be ratio 8%, unless made bold for end user benefit
  • Component font size should be "1"
    • e.g. R45, Q1, etc.
  • Layer - t/bPlace