RC13-KickerChipper - Revision history

Mbayyari3 at 00:52, 25 May 2020

2020-05-25T00:52:13Z

Mbayyari3 at 00:38, 25 May 2020

2020-05-25T00:38:06Z

Kberzinch3 at 02:00, 19 July 2018

2018-07-19T02:00:56Z

EJones at 15:42, 21 December 2014

2014-12-21T15:42:04Z

Rosawa3: recategorizing

2013-11-09T11:24:58Z

recategorizing

Rosawa3 at 07:04, 18 July 2013

2013-07-18T07:04:33Z

Rosawa3 at 13:05, 17 July 2013

2013-07-17T13:05:42Z

Rosawa3 at 13:04, 17 July 2013

2013-07-17T13:04:14Z

Nmitchell at 21:47, 3 October 2012

2012-10-03T21:47:47Z

Nmitchell at 21:46, 3 October 2012

2012-10-03T21:46:31Z

@@ Line 108: / Line 108: @@
 ##Use the mill to mill down the shaft to accommodate the kicker boot.
 #Rip off the casing of the push type solenoid to get the coil.
-[[Category:RoboCup]]<br/>[[Category: RC Mechanical]]<br/>[[Category:2012-2013]]
+[[Category: RC Mechanical]]<br/>[[Category:2012-2013]]

@@ Line 108: / Line 108: @@
 ##Use the mill to mill down the shaft to accommodate the kicker boot.
 #Rip off the casing of the push type solenoid to get the coil.
-[[Category:RoboCup]]<br/>[[Category:Mechanical]]<br/>[[Category:2012-2013]]
+[[Category:RoboCup]]<br/>[[Category: RC Mechanical]]<br/>[[Category:2012-2013]]

@@ Line 108: / Line 108: @@
 ##Use the mill to mill down the shaft to accommodate the kicker boot.
 #Rip off the casing of the push type solenoid to get the coil.
-[[Category:RoboCup]]<br/>[[Category:Mechanical]]<br/>[[Category:Year: 2012-2013|Year:_2012-2013]]
+[[Category:RoboCup]]<br/>[[Category:Mechanical]]<br/>[[Category:2012-2013]]

@@ Line 96: / Line 96: @@
 #Waterjet
 #Taps
-===Fabrication===
+=== Fabrication ===
 # Use the waterjet to cut the chipper arm sheet metal
-# The 3 axis CNC Mill is used to create the chipper boot; kicker boot; front,mid and rear mounts, and the plunger stabilizer.
+#Use the waterjet to cut the chipper arm sheet metal
 ##When milling the front solenoid mount make sure to put in the bushing in the pocket first before you mill the section.
-# Use the lathe and mill to create plunger.
+#Use the lathe and mill to create plunger.
-## To do this first create a hole in the both steel and stainless steel shafts with the lathe.
+##To do this, first create a hole in the both steel and stainless steel shafts with the lathe.
-## Thread holes with a 10-32 tap and attach both shafts with the set screw. Use retaining compound on the set screw.
+##Thread holes with a 10-32 tap and attach both shafts with the set screw. Use retaining compound on the set screw.
-## Now turn down the created shaft with lathe to the desired diameter.
+##Now turn down the created shaft with lathe to the desired diameter.
-## Cut Shaft to desired length.
+##Cut Shaft to desired length.
-## Use the mill to mill down the shaft to accommodate the kicker boot.
+##Use the mill to mill down the shaft to accommodate the kicker boot.
-# Rip of the casing of the push type solenoid to get the coil.
+#Rip off the casing of the push type solenoid to get the coil.
+[[Category:RoboCup]]<br/>[[Category:Mechanical]]<br/>[[Category:Year: 2012-2013|Year:_2012-2013]]

@@ Line 109: / Line 109: @@
 [[Category: RoboCup]]
-[[Category: RoboCup Mechanical]]
+[[Category: Mechanical]]
-[[Category: RoboCup 2013]]
+[[Category: Year: 2012-2013]]

← Older revision		Revision as of 07:04, 18 July 2013
Line 109:		Line 109:

	[[Category: RoboCup]]		[[Category: RoboCup]]
		+	[[Category: RoboCup Mechanical]]
	[[Category: RoboCup 2013]]		[[Category: RoboCup 2013]]

← Older revision		Revision as of 13:05, 17 July 2013
Line 108:		Line 108:
	# Rip of the casing of the push type solenoid to get the coil.		# Rip of the casing of the push type solenoid to get the coil.

		+	[[Category: RoboCup]]
	[[Category: RoboCup 2013]]		[[Category: RoboCup 2013]]

← Older revision		Revision as of 13:04, 17 July 2013
Line 107:		Line 107:
	## Use the mill to mill down the shaft to accommodate the kicker boot.		## Use the mill to mill down the shaft to accommodate the kicker boot.
	# Rip of the casing of the push type solenoid to get the coil.		# Rip of the casing of the push type solenoid to get the coil.
		+
		+	[[Category: RoboCup 2013]]

← Older revision		Revision as of 21:47, 3 October 2012
Line 106:		Line 106:
	## Cut Shaft to desired length.		## Cut Shaft to desired length.
	## Use the mill to mill down the shaft to accommodate the kicker boot.		## Use the mill to mill down the shaft to accommodate the kicker boot.
		+	# Rip of the casing of the push type solenoid to get the coil.

← Older revision		Revision as of 21:46, 3 October 2012
Line 96:		Line 96:
	#Waterjet		#Waterjet
	#Taps		#Taps
		+	===Fabrication===
		+	# Use the waterjet to cut the chipper arm sheet metal
		+	# The 3 axis CNC Mill is used to create the chipper boot; kicker boot; front,mid and rear mounts, and the plunger stabilizer.
		+	##When milling the front solenoid mount make sure to put in the bushing in the pocket first before you mill the section.
		+	# Use the lathe and mill to create plunger.
		+	## To do this first create a hole in the both steel and stainless steel shafts with the lathe.
		+	## Thread holes with a 10-32 tap and attach both shafts with the set screw. Use retaining compound on the set screw.
		+	## Now turn down the created shaft with lathe to the desired diameter.
		+	## Cut Shaft to desired length.
		+	## Use the mill to mill down the shaft to accommodate the kicker boot.