2015 Chipper - Revision history

Joldenburg6: Categorize

2018-06-14T01:49:42Z

Categorize

Snaeem at 19:54, 15 November 2015

2015-11-15T19:54:15Z

Snaeem at 19:53, 15 November 2015

2015-11-15T19:53:56Z

Snaeem at 19:53, 15 November 2015

2015-11-15T19:53:13Z

Amansour at 13:27, 19 June 2015

2015-06-19T13:27:44Z

Amansour at 13:26, 19 June 2015

2015-06-19T13:26:47Z

Amansour: Created page with "== The Goal == ==== The goal when creating the chipper was to simplify the design. We incorporated a Flat Solenoid as to fit the geometry of our robot. Esse..."

2015-06-19T13:26:33Z

Created page with "== The Goal == ==== The goal when creating the chipper was to simplify the design. We incorporated a Flat Solenoid as to fit the geometry of our robot. Esse..."

New page

== The Goal ==

==== The goal when creating the chipper was to simplify the design. We incorporated a [[Flat_Solenoid|Flat Solenoid]] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.  ====

← Older revision		Revision as of 01:49, 14 June 2018
Line 41:		Line 41:

	The maximum determined distance was still insufficient for the chipper to gain any significant vertical distance.		The maximum determined distance was still insufficient for the chipper to gain any significant vertical distance.
		+
		+	[[Category:RoboCup]][[Category:2015-2016]]

@@ Line 5: / Line 5: @@
 == Armature Distance Tests ==
-Tests were performed on 11/15/15 to test the distance the armature needs to be outside the chipper solenoid to maximize power output. The armature distance was measured from the front of the armature (the side without the hole).
+Tests were performed on 11/15/15 to test the distance the armature needs to be outside the chipper solenoid to maximize power output. The armature distance was measured from the front of the armature (the side without the hole). The spring remained unattached for all of the tests conducted.
 {| border="1" cellspacing="1" cellpadding="1" style="width:500px;"

@@ Line 5: / Line 5: @@
 == Armature Distance Tests ==
-Tests were performed on 11/15/15 to test the distance the armature needs to be outside the chipper solenoid to maximize power output.
+Tests were performed on 11/15/15 to test the distance the armature needs to be outside the chipper solenoid to maximize power output. The armature distance was measured from the front of the armature (the side without the hole).
 {| border="1" cellspacing="1" cellpadding="1" style="width:500px;"

← Older revision		Revision as of 19:53, 15 November 2015
Line 2:		Line 2:

	The goal when creating the chipper was to simplify the design. We incorporated a [http://wiki.robojackets.org/w/RC15-FlatSolenoid Flat Solenoid] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.		The goal when creating the chipper was to simplify the design. We incorporated a [http://wiki.robojackets.org/w/RC15-FlatSolenoid Flat Solenoid] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.
		+
		+	== Armature Distance Tests ==
		+
		+	Tests were performed on 11/15/15 to test the distance the armature needs to be outside the chipper solenoid to maximize power output.
		+
		+	{\| border="1" cellspacing="1" cellpadding="1" style="width:500px;"
		+	\|-
		+	\| '''Armature distance from front edge (in)'''
		+	\| '''Ball distance (in)'''
		+	\| '''1st bounce distance (in''')
		+	\|-
		+	\| .5
		+	\| 34.5
		+	\| 10.5
		+	\|-
		+	\| <span style="background-color:#FFD700;">.7</span>
		+	\| <span style="background-color:#FFD700;">40-44</span>
		+	\| <span style="background-color:#FFD700;">17</span>
		+	\|-
		+	\| .9
		+	\| -
		+	\|
		+	10
		+
		+	\|-
		+	\| 1.1
		+	\| 28
		+	\| 8.5
		+	\|-
		+	\| 1.3
		+	\| 14
		+	\| 4
		+	\|-
		+	\| 1.5
		+	\| 1.5
		+	\| 3
		+	\|}
		+
		+	The maximum determined distance was still insufficient for the chipper to gain any significant vertical distance.

← Older revision		Revision as of 13:27, 19 June 2015
Line 1:		Line 1:
	== The Goal ==		== The Goal ==

−	The goal when creating the chipper was to simplify the design. We incorporated a [[Flat Solenoid~~\|Flat Solenoid]~~] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.	+	The goal when creating the chipper was to simplify the design. We incorporated a [http://wiki.robojackets.org/w/RC15-FlatSolenoid Flat Solenoid] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.

← Older revision		Revision as of 13:26, 19 June 2015
Line 1:		Line 1:
	== The Goal ==		== The Goal ==

−	~~====~~ The goal when creating the chipper was to simplify the design. We incorporated a [[~~Flat_Solenoid~~\|Flat Solenoid]] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.  ~~====~~	+	The goal when creating the chipper was to simplify the design. We incorporated a [[Flat Solenoid\|Flat Solenoid]] as to fit the geometry of our robot. Essentially the solenoid armature slides barely touching the bottom plate hitting a pivot arm which the golf ball is resting on. This applies a force at a 55 degree angle upwards.